PVC

SOLID HOMOGENEOUS PVC

Floor Surfaces; Matting, Membranes, Etc.Anti-Slip; Abrasion-Resistant; "Rubberized"

• Thickness' – 1/16" (63 mil) (1.6mm) – 1/4" (250 mil) (6.35mm)
• Soft to hard durometer (hardness) or hardness modifications (flexible & semi-rigid)
• Weight modifications/specific gravity modifications
• Various in-house surface textures: Pebble; Stipple, Standard-Rib; Wide-Rib; Corrugated and large Pyramid embossing textures.
• Colors available – Minimum 7,500 square feet
• Clear/(Translucent) PVC available
• Poly film adhesive PSA available. Standard in 60" width
• Widths: 24" – 79"
• Lengths: 70' – 115' dependent upon the thickness and/or weight
• Rolls and Sheets
• "Rubberized" (elastomer-type) formulations available
• Thermoformable (See THERMFORM™)
• RF sealable PVC

SOLID AIR-INJECTED PVC

Floor Surfaces; Abrasion-Resistant; Matting, Membranes; "Rubberized"

Objective: To reduce the overall weight of the product as compared to a solid PVC without sacrificing the overall thickness.

• Thickness' – 80 mil (2.03mm) – 1/4" (250 mil) (6.35mm)
• Approximately 51 Durometer on Shore 'A' Scale
• Various in-house surface textures: Pebble; Stipple, Standard-Rib; Wide-Rib; Corrugated and large Pyramid embossing textures.– Textures on 80 mil to 1/4" thickness' only.
• Colors available – Minimum 7,500 square feet
• Clear/(Translucent) PVC available
• Poly film adhesive PSA available. Standard in 60" width
• Widths: 24" – 72"
• Lengths: 70' – 115' dependent upon the thickness and/or weight
• Rolls and Sheets
• "Rubberized" (elastomer-type) formulations available

THERMFORM™ Thermoformable flexible PVC

Floor Surfaces; Abrasion-Resistance; Matting, Liners, Barriers, Etc.

• Thickness' – 1/16" (63 mil) (1.6mm) – 1/4" (250 mils) (6.35mm) for homogeneous thermoformable material. Can coat as low as 35 mils as a thermoformable reinforcement on composite structures.
• Semi-rigid-80-95 durometer (hardness)
• Various in-house surface textures: Pebble; Stipple, Standard-Rib; Wide-Rib; Corrugated and large Pyramid embossing textures or non-embossed
• Colors available – Minimum 7,500 square feet
• Widths: 24" – 79"
• Lengths: 70' – 115' dependent upon the thickness and /or weight
• Rolls and Sheets
• "Rubberized" (elastomer-type) formulations available as component in composites.
• Standard parameters – 1:1 relationship of heating to cooling.

"Rule of Thumb" – 1 second of heating and cooing per every 1/1000th of an inch of the overall thickness of material being thermoformed. 2" vacuum hose provides optimum results as well as efficient cycle times.

PVCF™ Closed-cell PVC flexible foams

• Thickness' – 1/16" (63 mil) (1.6mm) – 3/4" (750 mils) (19mm) dependent upon the density.
• Density (Lbs per Cubic Foot) modifications –6#-30#+
• Low – high compression deflection formulations available
• 24" – 72" long widths (Belt back texture)
• 48" – 60" long widths casted on a release liner (smooth)
• High-tack formulations
• Colors available – minimum required – call Customer Service
• Surface texturing – embossings
• Anti-static formulations
• Rolls or Sheets
• Composites utiliing the PVC foams
• PVCF™ PFA – PVC foams with our PFA adhesives film technology

PFA (Poly Film Adhesive products)

Objective: To fusion-bond (natural/mechanical adhesion) a poly film adhesive to our products during our manufacturing process. There is a 1 mil Mylar® barrier separating the material nature and the adhesive making it capable to utilize different adhesive packages not risking plasticizer migration. This method insures that there will be NO delaminating of the adhesive from the product you adhered.

• 54" – 60" Standard 1 mil Mylar® poly film coated with 2-3 mils of an aggressive rubber-based polymer adhesive on a 78# heat-resistant liner.
• Other adhesive packages with volume can be exchanged for our standard adhesive system.

RV™ and RVP™ Technology

"Rubberized" elastomer-type materials

Objective: To camouflage ordinary PVC in its appearance to perform in most ways like rubber or pure elastomers.

• "Rubberized" enhances ordinary PVC by making it more skid-resistance by increasing its co-efficient of friction.
• "Rubberized" enhances ordinary PVC by making it more elastic or increasing its elongation %.
• "Rubberized" enhances ordinary PVC by mking it more elastic and increasing its tear strength.
• Thickness' – 1/16" (63 mil) (1.6mm) – 1/4" (250 mil ) (6.35mm) in AIRTUFF™ and solid PVC formulas.
• Various in-house surface textures: Pebble; Stipple, Standard-Rib; Wide-Rib; Corrugated and large Pyramid embossing textures.
• Colors available – Minimum 7,500 square feet
• Poly film adhesive PSA available. Standard is 60" wide.
• Widths: 24" – 79"
• Lengths: 70' – 115' dependent upon the thickness and/or weight
• Rolls and Sheets

NOYZ Products

Acoustical/NVH; Barriers; Isolation; Insulation; Dampeners; Composites; Absorbers

NOYZ TUFF Barriers:

• Barriers non-reinforced (.3#; .5#; .66#; .75#; 1.0#; 1.5#; 2.0#)
• Barriers reinforced
• Barriers; Clear 1.0# translucent
• Barrier Aluminum foil composite
• Barrier THERMFORM™ thermoformable barriers
• Barriers w/MYLAR® and aluminized fabric facings
• Barriers with acoustical embossings/surface textures
• Barriers that are UL94 & UL94 V-0 rated

NOYZ®PAD:

• NOYZ®TUFF Barriers fusion-bonded to a closed-cell PVC 8-10# density decoupler foam
• Acoustical Underlayment materials that are derivatives of the aforementioned

NOYZ®PAD II Composites: (2 layer)

• Barrier/decoupler (open-celled urethane)
• Barrier/decoupler ("shoddy" felt insulators)
• Barrier THERMFORM™/decoupler (open-celled urethane)

NOYZ®PAD III Composites: (3 layer)

• Barriers w/2layers of decouplers (open-celled urethane)
• Barriers/decoupler (open-celled urethane) PFA (Poly film adhesives)
• Barrier/decoupler layer with assorted facings

NOYZ®PAD Composites:

• NOYZ® TUFF Barrier layer of designed weight fusion-bonded to different abrasion-resistant matting top surface with assorted surface textures.
• NOYZ® TUFF Barrier layer of designed weight fusion-bonded to a top surface of a different abrasion-resistant matting thickness' with assorted surface textures.
• NOYZ® TUFF Barrier layer of designed weight fusion-bonded to thermoformable THERMFORM™ top surface of different abrasion-resistant matting thickness' with assorted surface textures.
• THERMFORM™ Barrier base fusion-bonded to a RV™ "rubberized" top surface, abrasion-resistant matting surface of different thickness'.

NOYZ®DAMP Isolation and Dampening materials:

• Light – heavy formulated PVC materials
• Different density PVC foams
• Composite structures
• Vapor Barriers
• Coated-fiberglass fabrics as a vapor or water-resistant barrier
• Woven fiberglass fabric/aluminum foil composite
• Heat-deflective Barriers/materials
• Foil fabric composites
• Foil/Insulating composites

NON-PVC

Thermoplastic Hybrids

TPO, TPR – Thermoplastic Hybrids. Material's consisting of rubber, Polypropylene and Polyethylene polymers. These materials can be utilized and manufactured like the aforementioned PVC products as homogeneous and composite products.